ide/exi doesnt work
-
- Posts: 448
- Joined: Mon Apr 05, 2010 4:11 pm
- Location: Germany
ide/exi doesnt work
hi,
today I build my ide/exi adapter. I messured every pin 3 times and everything seems good. After I connected it to my gamecube it doesnt work.
I used this:
http://www.gc-forever.com/gchdd/build.htm
now i think that my bluechip v9 which I used for it isnt programmed correctly. Swiss should recognize the ide exi without a harddrive hookd up. is this correctly? If yes, then my xilinx isnt flashed correctly. but which file do I have to flash, and which pins on the ide connectior have to be groundes?
Can anybody help me?
today I build my ide/exi adapter. I messured every pin 3 times and everything seems good. After I connected it to my gamecube it doesnt work.
I used this:
http://www.gc-forever.com/gchdd/build.htm
now i think that my bluechip v9 which I used for it isnt programmed correctly. Swiss should recognize the ide exi without a harddrive hookd up. is this correctly? If yes, then my xilinx isnt flashed correctly. but which file do I have to flash, and which pins on the ide connectior have to be groundes?
Can anybody help me?
Re: ide/exi doesnt work
sorry it this is a dumb question, but have you flashed the chip at all?
Re: ide/exi doesnt work
i sure didn't. sorry if made the impression, although i have no idea why it should've...infact wrote:sorry it this is a dumb question, but have you flashed the chip at all?
please search before you ask - a lot has been discussed already!
(or use google with "site:gc-forever.com *term*")
http://is.gd/MDmZcr
we also have a wiki filled with knowledge
http://is.gd/dX58Rm
(or use google with "site:gc-forever.com *term*")
http://is.gd/MDmZcr
we also have a wiki filled with knowledge
http://is.gd/dX58Rm
Re: ide/exi doesnt work
Firstly, you have to change the .ucf file to match your pins (or use the BlueChip v9 one), then you need to program the chip.yamaharacer wrote: now i think that my bluechip v9 which I used for it isnt programmed correctly. Swiss should recognize the ide exi without a harddrive hookd up. is this correctly? If yes, then my xilinx isnt flashed correctly. but which file do I have to flash, and which pins on the ide connectior have to be groundes?
Secondly, Swiss cannot find the adapter without a HDD attached (there is no EXI response ID in v1 of the firmware)
Lastly, look up the IDE pinout to figure out what needs to be connected to ground, and observe the orientation of the connector when doing so otherwise you could mess up the GC/Adapter/HDD.
-
- Posts: 448
- Joined: Mon Apr 05, 2010 4:11 pm
- Location: Germany
Re: ide/exi doesnt work
yeah i know that i have to program it but when i open the exi2ide.ipf file, it wants also to load an isp file but this file i dont have for the bluechip. i only can erase the xilinx nothing more.
-
- Posts: 448
- Joined: Mon Apr 05, 2010 4:11 pm
- Location: Germany
Re: ide/exi doesnt work
ok I read the tutorial once again and used ISE to generate my isp file. for this i changed the gc-ide.ucf file with the bluechip one, then I opened ISE and opened the ide2exi project. there I pressed "Implement Design" and "Rerun all".
Then I recognized that ISE has prepared me an isp file in the gc-ide folder. this file I have programmed to my xilinx.
Is this correct? If yes, I can search nor for hardware issues.
Then I recognized that ISE has prepared me an isp file in the gc-ide folder. this file I have programmed to my xilinx.
Is this correct? If yes, I can search nor for hardware issues.
Re: ide/exi doesnt work
You shouldn't need to re-generate the .Jed file, only configure the pin mappings and make sure they're OK.. after that start looking for he issues
-
- Posts: 448
- Joined: Mon Apr 05, 2010 4:11 pm
- Location: Germany
Re: ide/exi doesnt work
which jed file do you mean? when I extract the gcide.zip file there isnt any jed file. and where can i configure the pin mapping?
-
- Posts: 448
- Joined: Mon Apr 05, 2010 4:11 pm
- Location: Germany
Re: ide/exi doesnt work
ok I got it. the ucf file is wrong. A4 isnt pin 52 on the bluechip. its pin 36. here is the right ucf file and jed file for people who want to create a ide exi with bluechip.
- Attachments
-
- gcide.rar
- (9.24 KiB) Downloaded 458 times
Re: ide/exi doesnt work
There are 2types of bluechip, it's possible you just have the other type. I assume you got it working now?
-
- Posts: 448
- Joined: Mon Apr 05, 2010 4:11 pm
- Location: Germany
Re: ide/exi doesnt work
yeah, it works now but only one in 50 times. I think its a hardware problem with the data lines to the memory card. what lenght should the cables have?
edit: ok i got it. the cables were to long. now it works perfect.
edit: ok i got it. the cables were to long. now it works perfect.
Re: ide/exi doesnt work
thats the V9 yep.yamaharacer wrote:ok I got it. the ucf file is wrong. A4 isnt pin 52 on the bluechip. its pin 36. here is the right ucf file and jed file for people who want to create a ide exi with bluechip.
the file is preconfigured for V10
please search before you ask - a lot has been discussed already!
(or use google with "site:gc-forever.com *term*")
http://is.gd/MDmZcr
we also have a wiki filled with knowledge
http://is.gd/dX58Rm
(or use google with "site:gc-forever.com *term*")
http://is.gd/MDmZcr
we also have a wiki filled with knowledge
http://is.gd/dX58Rm
-
- Posts: 448
- Joined: Mon Apr 05, 2010 4:11 pm
- Location: Germany
Re: ide/exi doesnt work
ok that says also why my other bluechip that I have build a year ago never worked.
Re: ide/exi doesnt work
my : Buy : blue chip 10 / pcb v9yamaharacer wrote:ok that says also why my other bluechip that I have build a year ago never worked.
could make the cable to be recognized, I reduced the size of the cable and used an external power from a battery (2032) 3.3v, only now it's time to "program" it gives this error:
Welcome to iMPACT
iMPACT Version: 10.1
// *** BATCH CMD : loadProjectFile -file "C:\Documents and Settings\Administrador\Desktop\gcide\exi2ide.ipf"
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
LPT base address = 0378h.
ECP base address = 0778h.
Cable connection established.
INFO:iMPACT:2676 - base class function getDeviceChain(index) is called.
INFO:iMPACT:2676 - base class function getDeviceChain(index) is called.
INFO:iMPACT:2676 - base class function getDeviceChain(index) is called.
'1': Loading file 'C:/Documents and Settings/Administrador/Desktop/gc_ide.jed' ...
done.
INFO:iMPACT:1777 -
Reading C:/Xilinx/10.1/ISE/xc9500xl/data/xc95144xl.bsd...
INFO:iMPACT:501 - '1': Added Device xc95144xl successfully.
----------------------------------------------------------------------
----------------------------------------------------------------------
Active mode is BS
// *** BATCH CMD : setMode -ss
// *** BATCH CMD : setMode -sm
// *** BATCH CMD : setMode -hw140
// *** BATCH CMD : setMode -spi
// *** BATCH CMD : setMode -acecf
// *** BATCH CMD : setMode -acempm
// *** BATCH CMD : setMode -pff
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : Program -p 1 -e -v
INFO:iMPACT:583 - '1': The idcode read from the device does not match the idcode in the bsdl File.
INFO:iMPACT:1578 - '1': Device IDCODE : 00001111111111111111111111111111
INFO:iMPACT:1579 - '1': Expected IDCODE: 00001001011000001000000010010011
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
PROGRESS_START - Starting Operation.
which may be?
Please help !!!!!!
if I can not run it this week I will sell my gamecube and abandon this "EXI diy" because I'm losing too much time trying something that does not work !