IDE-EXI - Revision history

Lumina33: /* General information */ bolded title

2024-07-20T14:30:29Z

General information: bolded title

← Older revision		Revision as of 10:30, 20 July 2024
Line 27:		Line 27:

	== General information ==		== General information ==
	The IDE-EXI originated from a design by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the IDE-EXI.		The '''IDE-EXI''' originated from a design by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the IDE-EXI.
	[[Image:ide-exi-gc.jpg\|thumb\|alt=Gamecube with IDE-EXI connected\|Gamecube with IDE-EXI connected\|300px\|right\|Gamecube with IDE-EXI connected in Slot B]]		[[Image:ide-exi-gc.jpg\|thumb\|alt=Gamecube with IDE-EXI connected\|Gamecube with IDE-EXI connected\|300px\|right\|Gamecube with IDE-EXI connected in Slot B]]

Lumina33: Lumina33 moved page Ide-exi to IDE-EXI: all caps title like it appears in page body

2024-07-20T14:29:29Z

Lumina33 moved page Ide-exi to IDE-EXI: all caps title like it appears in page body

← Older revision	Revision as of 10:29, 20 July 2024
(No difference)

Lumina33: /* General information */ removed duplicate word

2024-07-20T02:15:09Z

General information: removed duplicate word

← Older revision		Revision as of 22:15, 19 July 2024
Line 27:		Line 27:

	== General information ==		== General information ==
	The IDE-EXI originated from a design by by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the IDE-EXI.		The IDE-EXI originated from a design by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the IDE-EXI.
	[[Image:ide-exi-gc.jpg\|thumb\|alt=Gamecube with IDE-EXI connected\|Gamecube with IDE-EXI connected\|300px\|right\|Gamecube with IDE-EXI connected in Slot B]]		[[Image:ide-exi-gc.jpg\|thumb\|alt=Gamecube with IDE-EXI connected\|Gamecube with IDE-EXI connected\|300px\|right\|Gamecube with IDE-EXI connected in Slot B]]

Extrems at 23:18, 4 October 2021

2021-10-04T23:18:00Z

← Older revision		Revision as of 19:18, 4 October 2021
Line 21:		Line 21:
	\|data4 = IDE Hard Disk Drive		\|data4 = IDE Hard Disk Drive
	\|label5 = Max Supported		\|label5 = Max Supported
	\|data5 = ~~2TB~~		\|data5 = 128PB
	\|label6 = SATA IC (M.2 Loader only)		\|label6 = SATA IC (M.2 Loader only)
	\|data6 = JMicron JM20330		\|data6 = JMicron JM20330

Extrems at 23:37, 20 September 2021

2021-09-20T23:37:36Z

← Older revision		Revision as of 19:37, 20 September 2021
Line 23:		Line 23:
	\|data5 = 2TB		\|data5 = 2TB
	\|label6 = SATA IC (M.2 Loader only)		\|label6 = SATA IC (M.2 Loader only)
	\|data6 = ?		\|data6 = JMicron JM20330
	}}		}}

Emu kidid: Add minimal M.2 loader mention

2021-09-20T23:33:03Z

Add minimal M.2 loader mention

← Older revision		Revision as of 19:33, 20 September 2021
Line 22:		Line 22:
	\|label5 = Max Supported		\|label5 = Max Supported
	\|data5 = 2TB		\|data5 = 2TB
			\|label6 = SATA IC (M.2 Loader only)
			\|data6 = ?
	}}		}}

Line 28:		Line 30:
	[[Image:ide-exi-gc.jpg\|thumb\|alt=Gamecube with IDE-EXI connected\|Gamecube with IDE-EXI connected\|300px\|right\|Gamecube with IDE-EXI connected in Slot B]]		[[Image:ide-exi-gc.jpg\|thumb\|alt=Gamecube with IDE-EXI connected\|Gamecube with IDE-EXI connected\|300px\|right\|Gamecube with IDE-EXI connected in Slot B]]

	== ~~Release~~ ==		== Support ==
	There was a batch of 100 IDE-EXI's produced and sold at GC-Forever, they sold within a day or two. A few months after, the files to have your own (mass) produced were [http://www.gc-forever.com/forums/viewtopic.php?f=23&t=538 released]. No more have been produced to this date, however users can always build their own all that is required is the Xilinx and time :)		The IDE-EXI has its own dedicated [https://www.gc-forever.com/forums/viewforum.php?f=23 sub forum].

			== IDE-EXI Availability ==
			There was a batch of 100 IDE-EXI's produced and sold at GC-Forever, they sold within a day or two. A few months after, the files to have your own (mass) produced were [http://www.gc-forever.com/forums/viewtopic.php?f=23&t=538 released]. Badassconsoles produced a second batch at some point which were released to the public. No more have been produced to this date on a large scale, however users can always build their own all that is required is the Xilinx and time :)
	[[Image:ide-exi-back.jpg\|thumb\|alt=IDE-EXI back showing credits\|IDE-EXI back showing credits\|300px\|right\|IDE-EXI back showing credits]]		[[Image:ide-exi-back.jpg\|thumb\|alt=IDE-EXI back showing credits\|IDE-EXI back showing credits\|300px\|right\|IDE-EXI back showing credits]]

	== ~~Bugs~~ ==		== M.2 Loader ==
			webhdx released a variant of the IDE-EXI with a in-built SATA to IDE IC (with a M.2 connector) for Serial Port 1. This is based on the version 2 DMA fixed [https://www.gc-forever.com/forums/viewtopic.php?f=23&t=4843 source code] and has support integrated into Swiss itself now.

			== IDE-EXI limitations ==
	The Gamecube EXI bus has a bug in which every time data goes across the input line, the same data is written back out shifted right by 1. Due to this, the initial code cannot have DMA transfers performed, which limits speed (not 100% confirmed at this point).		The Gamecube EXI bus has a bug in which every time data goes across the input line, the same data is written back out shifted right by 1. Due to this, the initial code cannot have DMA transfers performed, which limits speed (not 100% confirmed at this point).
	isobel from gc-linux.org has [http://www.gc-linux.org/wiki/EXI:IDEHostAdapter fixed] this bug, <s>however this is in testing at the moment</s>.		isobel from gc-linux.org has [http://www.gc-linux.org/wiki/EXI:IDEHostAdapter fixed] this bug, <s>however this is in testing at the moment</s>.

Emu kidid at 22:15, 17 December 2014

2014-12-17T22:15:58Z

← Older revision		Revision as of 18:15, 17 December 2014
Line 34:		Line 34:
	== Bugs ==		== Bugs ==
	The Gamecube EXI bus has a bug in which every time data goes across the input line, the same data is written back out shifted right by 1. Due to this, the initial code cannot have DMA transfers performed, which limits speed (not 100% confirmed at this point).		The Gamecube EXI bus has a bug in which every time data goes across the input line, the same data is written back out shifted right by 1. Due to this, the initial code cannot have DMA transfers performed, which limits speed (not 100% confirmed at this point).
	isobel from gc-linux.org has [http://www.gc-linux.org/wiki/EXI:IDEHostAdapter fixed] this bug, however this is in testing at the moment.		isobel from gc-linux.org has [http://www.gc-linux.org/wiki/EXI:IDEHostAdapter fixed] this bug, <s>however this is in testing at the moment</s>.

			DMA Support was tested but what occurs is that if you DMA more than 1 sector of data over, the GameCube will DMA read too fast for the HDD to have prepared the data for the second sector. This causes random garbage bytes to appear mid DMA stream. More testing at slower speeds is required and single sector DMA too.

	[[Category:MiscHardware]]		[[Category:MiscHardware]]

Emu kidid at 03:52, 19 March 2012

2012-03-19T03:52:49Z

← Older revision		Revision as of 23:52, 18 March 2012
Line 26:		Line 26:
	== General information ==		== General information ==
	The IDE-EXI originated from a design by by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the IDE-EXI.		The IDE-EXI originated from a design by by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the IDE-EXI.
			[[Image:ide-exi-gc.jpg\|thumb\|alt=Gamecube with IDE-EXI connected\|Gamecube with IDE-EXI connected\|300px\|right\|Gamecube with IDE-EXI connected in Slot B]]

	== Release ==		== Release ==
	There was a batch of 100 IDE-EXI's produced and sold at GC-Forever, they sold within a day or two. A few months after, the files to have your own (mass) produced were [http://www.gc-forever.com/forums/viewtopic.php?f=23&t=538 released]. No more have been produced to this date, however users can always build their own all that is required is the Xilinx and time :)		There was a batch of 100 IDE-EXI's produced and sold at GC-Forever, they sold within a day or two. A few months after, the files to have your own (mass) produced were [http://www.gc-forever.com/forums/viewtopic.php?f=23&t=538 released]. No more have been produced to this date, however users can always build their own all that is required is the Xilinx and time :)
			[[Image:ide-exi-back.jpg\|thumb\|alt=IDE-EXI back showing credits\|IDE-EXI back showing credits\|300px\|right\|IDE-EXI back showing credits]]

	== Bugs ==		== Bugs ==

Emu kidid at 03:45, 19 March 2012

2012-03-19T03:45:25Z

← Older revision		Revision as of 23:45, 18 March 2012
Line 25:		Line 25:

	== General information ==		== General information ==
	The IDE-EXI originated from a design by by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the [[IDE-EXI]].		The IDE-EXI originated from a design by by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the IDE-EXI.

	== Release ==		== Release ==

Emu kidid: Created page with "{{Infobox |name = Infobox/doc |bodystyle = |title = IDE-EXI |titlestyle = |image = alt=IDE-EXI |imagestyle = |caption ..."

2012-03-19T03:43:35Z

Created page with "{{Infobox |name = Infobox/doc |bodystyle = |title = IDE-EXI |titlestyle = |image = 200px|alt=IDE-EXI |imagestyle = |caption ..."

New page

{{Infobox
|name = Infobox/doc
|bodystyle =
|title = IDE-EXI
|titlestyle =

|image = [[File:ide-exi.jpg|200px|alt=IDE-EXI]]
|imagestyle =
|caption = IDE-EXI
|captionstyle =
|headerstyle = background:#ccf;
|labelstyle = background:#ddf;
|datastyle = background:#ddf;

|header1 = Specification
|label2 = CPU
|data2 = Xilinx XC95144XL
|label3 = GC Interface
|data3 = Memory Card Slot A/B
|label4 = HDD Interface
|data4 = IDE Hard Disk Drive
|label5 = Max Supported
|data5 = 2TB
}}

== General information ==
The IDE-EXI originated from a design by by Dampro (Damián), where he wanted to use whatever electronics he had lying around to get his GC to boot backups via modifying SD-Boot. His initial design/spec/code/tutorial is located [http://www.gc-forever.com/gchdd/build.htm here] and is intended for those who already have some device (PS2 Xilinx based modchip) for parts. The code was re-used in a redesigned version intended for the memory card slot with the help of bushing from Team Twiizers designing the PCB - this is what everyone has known as the [[IDE-EXI]].

== Release ==
There was a batch of 100 IDE-EXI's produced and sold at GC-Forever, they sold within a day or two. A few months after, the files to have your own (mass) produced were [http://www.gc-forever.com/forums/viewtopic.php?f=23&t=538 released]. No more have been produced to this date, however users can always build their own all that is required is the Xilinx and time :)

== Bugs ==
The Gamecube EXI bus has a bug in which every time data goes across the input line, the same data is written back out shifted right by 1. Due to this, the initial code cannot have DMA transfers performed, which limits speed (not 100% confirmed at this point).
isobel from gc-linux.org has [http://www.gc-linux.org/wiki/EXI:IDEHostAdapter fixed] this bug, however this is in testing at the moment.

[[Category:MiscHardware]]