Hi unfortunately back again, sorry psyko_chewbacca i have yet to run swiss on my console. but it IS a dol-001 rev A with dol-cpu-20 in it and NTSC. I can confirm both chips work with my gamecube, so seeing as it's yet unsupported i would imagine it's higher than 1.0. I agree with yamaharacer, GC's a...

Update again, i've updated the wode firmware to 2.8a and that works!!. WOOT finally after a little over a week i have a working wode. now to dremel out the case and make it nice and sleek. Thanks for your help/suggestions guys.

So i'm at a new point now, im glad i had the wiikey to test with otherwise i'de be pulling my hair out. my wiikey works about 90% occasionally i get the error message but it seems like it when it's loading not randomly from shutting off.. The wode still gets the symptoms i've posted before, gamecube...

update again, Woot got the wiikey running, kinda. i might have a little cable touching somewhere requires further investigation. i can get it to boot most of the time, it will boot into the wiikey menu then restart when i select "mounting" the first try it detected the game(wind waker) and...

Just an update, i installed my eject button, 1.9 from regulator to no, pin 29 to c, and ground to nc. no effect. i did notice a little cange in functionality. when i start the gamecube with the lid switch closed and an sd card in the wiikey, the gamecube loads up fine, doesn't error, but wont read t...

So i picked up a wiikey fusion today to run some tests on this cube. seems to me i have a ipl 1.0 as neither the wiikey nor wode will run and my gamecube is most likely a dol-01 rev a(as stated in my previous post). Has almost the same symptoms, gamecube will error most of the time. on with lid swit...

Ashen my mobo revision is a dol-001 rev a i think as it has the digital av and serial port 2, printed on the mobo is this "..c/dol-cpu-20". it's a usa console so ntsc, my region in the wode settings is region US, autoboot off, update off, game patching off(i think thats what it's called). ...

so i've check checked and rechecked all my wires, there are no shorts/touching wires. the only wires that ARE touching are 2,4,6,8,10,12,14,16,18,20 and 29. they all go to the regulator spot. now for my symptoms, my gamecube is running but i keep getting the message. i've updated from 1.0 to 2.8 rea...

got my cube running, it ws my 5 volt line. was a cold weld so it was shorting out. i fixed the problem by taking my wires apart and soldering them 1wire to 1 pin. i've split up my cables on the regulator for ease and permanent soldering. i plugged my wode in and found it not working again. checked m...

So i've rebuilt my flex cable for a third time, this time i got it. it's sturdy and nice and short free. i've ended up cutting it down to about 2.5 inches total. I tested every lead as i did them and throughout. no shorts/pins touching. no broken cable ends it's all good. but now i have a symptom wi...

just checked my flex cable, i used the back of the wode (host) connector to check for continuity, i have 2 wires that are shorting, i suppose i'll cut the *bleeping* flex cable again and try to get it done right. 3rd times the charm..i hope. will report back when done.

so i chopped and rebuilt my flex cable today. no luck. my host power connector had a bent pin in it so i removed the connector and wired direct. my wode seems to be working, it loads up, loads iso's, but still i'm getting the message on screen. i updated from 2.8 read/write to 2.8 read only. no diff...

Some progress but still going. i've removed my dvd rom's connector, removed pins im not using, and wired it up. i cut about half an inch back in my cabling so i'm now at 4.5 inch. i've installed my usb power for the wode from 5 volt power off the regulator. I've removed my grounds from my dvd slot a...

So over the course of today i have had little success, i now know i can connect the wode usb to 5 volt so thats one question answered through research. I'm warming my soldering iron now to remove my dvd conector wires as that seems to be where i'm getting the problem. as i said before when the wode ...

Hi my name is Xero, this is my first post in these forums, though i can say i've been reading them for some time. If the answers i'm looking for were out there, they sure hid them well..but i am pretty tired. anyway on to it shall we. So i've decided to spruce up my old gamecube after all these year...